Beam Clamp for Manual Electric Hoist with Shackle

Beam Clamp for Manual Electric Hoist with Shackle

Beam Clamp for Handbook/CZPT CZPT with Shackle (BCS Variety)


-H-Raise beam clamps act as a semi-permanent attachment level for guide hoists or electrical hoists.

-Functioning load restrict up to ten tons.

-Ideal for use with electric powered hoists and chain blocks.

-Pivoting eye to connect a hoist.

-Very easily adjustbale to fit most beams by turning central threaded changing bar.

Model BCS571 BCS571 BCS030 BCS050 BCS100
Capacity                     T 1 2 three 5 10
Proof Load                 kN 29.four 44.1 73.five 147
Beam Width               mm 75-230 seventy five-230 100-250 one hundred twenty five-270 one hundred thirty-2320
proportions(mm) A max 240 240 260 280 330
B min 204 204 251 263 324
max 377 377 426 445 547
C 119.five 138.five a hundred sixty five 213 267
D five 7 eight 10 sixteen
E 212 212 260 270 312
F min ninety four 94 169 183 192
max 149 149 207 224 245
G seventeen seventeen fifty three 57 55
H forty two.five fifty fifty seven.5 72.5 ninety one.5
Internet Weight                kg five.9 seven.5 12.four 18 36


•Store and take care of beam clamps correctly. 
•Inspect beam clamps and accessories ahead of use and before inserting into storage. 
•Ensure the supporting construction is ample for the full load that will be imposed and suited for the application. 
•Check the clamp is of the right profile and dimension, or correctly modified, for the beam width and that it seats properly on the 
beam flange. 
•Ensure the beam clamp is robust adequate for the full load that will be imposed. 
•Check that the clamp is directly in excess of the centre of gravity of the load.

By no means: 
•Use beam clamps which are unknown or uncertified for lifting programs. 
•Never change bolts, shackles etc CZPT consulting the supplier. 
• Toss or drop beam clamps. 
• Use beam clamps on ruined or distorted beams. 
•Force or wedge hooks of lifting appliances into the attachment eye or fitting (eg shackle). 
•Obliquely load beam clamps CZPT the authority of the supplier.

Usually Asked Concerns

Q1. How often ought to lifting equipments be subject to complete examantions?

Thorough examination of lifting products have to consider area every 12 months – or every 6 months if the tools is utilized to lift folks. Any add-ons used in lifting need to also be inspected every single 6 months. These are the bare minimum needs, in which there is no official ‘examination scheme’ drawn up by a proficient man or woman.

Q2. What is a qualified individual ?

A competent person is someone who has suitable sensible and theoretical understanding and expertise of the equipment for which they act as ‘competent person’. This expertise and knowledge can support them detect defects / weaknesses and evaluate regardless of whether they will have an effect on the ongoing safe use of the tools.

Q3. Does new lifting equipment have to be extensively examined just before use ?

You have to have lifting tools examined in the pursuing situation:

Prior to using it for the 1st time – until the gear has an EC Declaration of Conformity which is considerably less than one particular yr outdated and the lifting gear was not assembled on site. If it was assembled on web site, it must be examined by a capable individual to validate that the assembly was correct and protected.
After assembly, and just before use at every place – for all lifting gear that calls for assembly or set up before use (eg tower crane) – to make certain it has been installed correctly and is protected for use


Beam Clamp for Manual Electric Hoist with Shackle


Mill Chain

As one of the leading mill chain manufacturers, suppliers, and exporters of mechanical products, We offer mill chains and many other products.

Please contact us for details.

Manufacturer supplier exporter of the mill chain.

Recent Posts